- Chapters
- descriptions off, selected
- default, selected
This is a modal window.
Beginning of dialog window. Escape will cancel and close the window.
End of dialog window.
Uuden sukupolven ensiluokkainen pintamaalijärjestelmä. Helppokäyttöisellä yksikomponenttimaalilla lopputulos on ammattimainen.
Toplac Plus antaa parhaan korkeakiiltoisen pinnan ja pitkäkestoisemman UV-suojan. Maali on helppo levittää telalla eikä erillistä tasoitusta tarvita. Saatavissa laaja valikoima värisävyjä.
Eri maissa saatavilla olevat värit löytyvät osoitteesta international-yachtpaint.com
Saatavilla olevat värit
Valitse väri
White
YLK905 (905)
Snow White
YLK000 (001)
Mediterranean White
YLK184 (545)
Oyster White
YLK194 (195)
Off White
YLK192 (193)
Ivory
YLK187 (812)
Matterhorn White
YLK198 (199)
Platinum
YLK151 (151)
Atlantic Gray
YLK684 (289)
Cream
YLK027 (027)
Yellow
YLK101 (101)
Rescue Orange
YLK265 (265)
Fire Red
YLK504 (504)
Rochelle Red
YLK299 (011)
Rustic Red
YLK501 (501)
Bounty
YLK292 (350)
Donegal Green
YLK541 (077)
Bondi Blue
YLK898 (016)
Lauderdale Blue
YLK936 (936)
Sapphire Blue
YLK830 (830)
Oxford Blue
YLK993 (105)
Mauritius Blue
YLK904 (018)
Flag Blue
YLK990 (992)
Jet Black
YKL999 (051)
Toplac Plus
Ensiluokkainen erittäin kestävä kiiltävä pinta
Ammattilaatuinen lopputulos
Parannettu UV-suoja säilyttää kiillon ja värit
Erinomainen kiilto
Uuden juoksevamman koostumuksen ansiosta telaa käytettäessä ei tarvetta erilliselle tasoitukselle
Ei hiontaa kerrosten välillä
Lue lisää
Levitä One UP:n päälle, yksiosainen pohjamaalimme ja pohjamaalimme kaikki yhdessä, alustan suojauksella, erittäin sileällä pinnalla ja alhaisemmalla VOC-pitoisuudella.
One UP Viskositeetti ja sekoitus
One UP
Primeri-pohjamaaliyhdistelmä viimeistelypinnoille
Yksinkertaisempi järjestelmä metallisille alustamateriaaleille
Tasaisempi lopputulos ja parempi alustan suoja
Suunniteltu parantamaan Toplac Plus -pintamaalin ulkonäköä
Luokkansa paras järjestelmä International-yksikomponenttisten pinta- ja kansimaalien kanssa kaikille alustamateriaaleille
1. Tuote saattaa avattaessa näyttää ja tuntua kiinteältä tai viskoosiselta.
2. Jos tuotetta ei ole sekoitettu, sen voi kääntää ylösalaisin ilman, että se valuu ulos purkista.
Vähemmän haihtuvia orgaanisia yhdisteitä
Helppo levittää siveltimellä tai telalla ja lisäksi hyvin juokseva ja erinomaisesti tasoittuva
Helpompi hioa kuin Pre-Kote, mikä lyhentää kerrosten välillä tarvittavaa odotusaikaa
3. One UP täytyy sekoittaa huolellisesti, jotta koostumus on oikeanlainen.
4. Perusteellisen sekoittamisen jälkeen maalin tulisi olla juoksevaa, jolloin se on käyttövalmista.
Lue lisää
One UP-maalin sekoitus
Loistavan lopputuloksen saavuttaminen ei ole koskaan ollut näin helppoa.
- Chapters
- descriptions off, selected
- default, selected
This is a modal window.
Beginning of dialog window. Escape will cancel and close the window.
End of dialog window.
Got questions? Check out our FAQ's
Pre-Kote Plus FAQ's
Toplac Plus FAQ's
Questions and answers
Questions and answers
Can Toplac Plus be applied over recently applied Brightside?
Yes, with light sanding with P400.
Can Brightside be mixed with Toplac Plus?
No. To avoid wasting any Brightside you might use it either as a first
coat before switching to Toplac Plus.
Can Toplac Plus be blended with Pre-Kote Plus?
Yes, follow recommendations as for Toplac Plus.
Can Toplac Plus be applied over Pre-Kote?
Yes, but the enhanced gloss and DOI levels of Toplac Plus may not be fully obtained.
Is Toplac Plus suitable for use on decks with Intergrip added, or
will it be too slippery?
We would recommend the use of Interdeck for decks. Toplac Plus would present the same finish as Brightside with Intergrip added and both would have very similar levels of slip resistance. Actual levels of slip resistance would vary depending on the level of Intergrip added and how evenly it was applied.
Do Toplac Plus colors match the previous Brightside colors
where the color name are the same?
Toplac Plus is not an exact match to Brightside due the new raw
materials used in Toplac Plus, but as with any manufactured color you should always ensure you have the same batch number product to complete any given job. Using Brightside with Toplac Plus of the same
Can Pre-Kote Plus and Pre-Kote be physically mixed together?
No, they are not fully compatible with each other.
Can Pre-Kote Plus be applied over Pre-Kote if half-way through a job?
Yes.
Can Pre-Kote be applied over Pre-Kote Plus?
Yes, but not recommended as the full properties of Toplac Plus
may not be obtained.
Can Toplac be blended with Pre-Kote Plus?
Yes, follow recommendations as for Toplac Plus.
Can Pre-Kote Plus be applied over Interprotect?
Yes.
I have previously used a primer in timber bilges without overcoating because it was fast dry and easy to apply. Could I use Pre-Kote Plus for the same type of job?
Yes, but use the Blue-Gray product.
code/color side by side for example may well show a tonal difference that can be affected by very slight color differences andgloss levels. It is best to use any Brightside you have as a first coat, perhaps blended with Pre-Kote Plus and finish with Toplac Plus.
Can I add other products/additives to Toplac Plus?
No, you should never add any additives or materials that claim to improve specific properties of an AkzoNobel product unless it is specifically stated so on the technical data sheet or labels. Doing so would invalidate any claims for application or performance issues. Flattening Agent for one part finishes can be used to create a variety of gloss, satin or matt effects.
Can the product be sprayed?
We do not recommend that DIY users spray the product as it is unlikely that they would have the full correct PPE equipment and suitable ventilated application areas. Professionals may decide to spray apply the product as they would have both. If sprayed Special Thinner 216 is recommended for Toplac Plus.
What equipment (roller/brush) should I use with Toplac Plus?
We recommend to use a fine, thermo-bonded foam roller. Suitable rollers are listed below:
4” High Density Foam Rollers (rounded edges)
6” Closed Cell Foam Rollers (flat edges, cut into 3” sections)
6” Ultra Smooth High Density Foam Rollers (rounded edges)
If a brush is required then any natural bristle brush would be recommended.
Can Pre-Kote Plus be used on Clear Epoxies like West System, Hawk Epoxy, or System Three epoxies?
No, it cannot not be directly applied due to the amine in the epoxy. Recommend to use either Epoxy Primekote 404/414 or InterProtect 2000E over this substrate and then finish off with Pre-Kote Plus as the final primer prior to topcoat.
Would the White Pre-Kote Plus yellow if used in interior and not overcoated with gloss finish?
Most single part finishes tend to yellow in the dark but recover if exposed to light. For example, if used in dry bilge areas it would be wise to use the Blue-Gray Pre-Kote Plus as any yellowing would not be so noticeable.
Can I add other products/additives to Pre-Kote Plus?
No, you should never add any additives or materials that claim to improve specific properties of an AkzoNobel product unless it is specifically stated so on the technical data sheet or labels. Doing so would invalidate any claims for application or performance issues.
Can the product be sprayed?
We do not recommend that DIY users spray the product as it is unlikely that they would have the full correct PPE equipment and suitable ventilated application areas. Professionals may decide to spray apply the product. Pre Kote Plus can be sprayed with Special Thinner 216.
Lue lisää Toplac Plus- ja One UP -maalien hyödyistä.
Lataa
Etsi jälleenmyyjä
osta nyt
Tarvitsetko lisää apua? Ota yhteyttä.
maritim@maritim.fi