Vi presenterer vårt nestegenerasjons førsteklasses malingssystem, som gir profesjonelle resultater, er enkelt å bruke og kommer som énkomponentløsning.
Toplac Plus gir en førsteklasses, høyblank finish med mer langvarig UV-beskyttelse, og er enkel å påføre med rulle, uten at det er nødvendig å etterstryke med pensel. Den finnes i et utvalg av klare, sterke farger.
Gå til international-yachtpaint.com for å se tilgjengelige farger i ulike land
Snow White
YLK000 (001)
Mediterranean White
YLK184 (545)
Matterhorn White
YLK198 (199)
Rescue Orange
YLK265 (265)
Oyster White
YLK194 (195)
Ivory
YLK187 (812)
Cream
YLK027 (027)
Fire Red
YLK504 (504)
Mauritius Blue
YLK904 (018)
Rustic Red
YLK501 (501)
Bondi Blue
YLK898 (016)
Lauderdale Blue
YLK936 (936)
Sapphire Blue
YLK830 (830)
Oxford Blue
YLK993 (105)
Flag Blue
YLK990 (992)
Platinum
YLK151 (151)
Atlantic Gray
YLK684 (289)
Jet Black
YKL999 (051)
Yellow
YLK101 (101)
Rochelle Red
YLK299 (011)
Bounty
YLK292 (350)
Donegal Green
YLK541 (077)
One UP
2-i-1 grunning og mellomstrøk som énkomponentløsning
Mindre komplisert system for metallflater
Gir en jevnere finish med ekstra underlagsbeskyttelse
Med formel som forbedrer utseendet til Toplac Plus
Et førsteklasses system med énkomponents lakk- og dekksmalinger fra International, for alle underlag
Lavere VOC-innhold
Påføres enkelt med pensel eller rulle, og har svært gode utflytings- og utjevningsegenskaper
Lettere å pusse enn Pre-Kote, noe som reduserer tidsbruken mellom hvert strøk
Finn ut hvordan du blander One UP
Påfør over One UP, vår énkomponents grunning og primer i ett, med underlagsbeskyttelse, en ekstra glatt finish og lavare VOC.
Toplac Plus
Førsteklasses slitesterk båtlakk med høy glans
Profesjonell finish av høy kvalitet
Den nye formelen med forbedret utflyting eliminerer behovet for å stryke over med pensel etterpå når du bruker rulle
Ingen sliping mellom strøkene
Forbedret UV-beskyttelse gir glans og fargeholdbarhet
Ekstra høy glans
Finn ut mer
Det har aldri vært enklere å oppnå en fantastisk finish.
Got questions? Check out our FAQ's
Pre-Kote Plus FAQ's
Toplac Plus FAQ's
Last ned
Last ned brosjyren for å finne ut mer om hva Toplac Plus og One UP kan tilby deg.
Finn en forhandler
handle nå
Trenger du fortsatt hjelp? Ta kontakt med oss.
iyp.norge@akzonobel.com
Tilgjengelige farger
Velg en farge
One UP Viskositet og blanding
1. Ved åpning kan dette produktet være tykt.
2. Hvis det ikke blandes, kan det hende at produktet ikke renner fra boksen når den snus opp ned.
3. One UP må blandes grundig for å oppnå riktig konsistens.
4. Når produktet er godt blandet, vil det renne ut av boksen og er dermed klart til bruk.
Questions and answers
Can Pre-Kote Plus and Pre-Kote be physically mixed together?
No, they are not fully compatible with each other.
Can Pre-Kote Plus be applied over Pre-Kote if half-way through a job?
Yes.
Can Pre-Kote be applied over Pre-Kote Plus?
Yes, but not recommended as the full properties of Toplac Plus
may not be obtained.
Can Toplac be blended with Pre-Kote Plus?
Yes, follow recommendations as for Toplac Plus.
Can Pre-Kote Plus be applied over Interprotect?
Yes.
I have previously used a primer in timber bilges without overcoating because it was fast dry and easy to apply. Could I use Pre-Kote Plus for the same type of job?
Yes, but use the Blue-Gray product.
Can Pre-Kote Plus be used on Clear Epoxies like West System, Hawk Epoxy, or System Three epoxies?
No, it cannot not be directly applied due to the amine in the epoxy. Recommend to use either Epoxy Primekote 404/414 or InterProtect 2000E over this substrate and then finish off with Pre-Kote Plus as the final primer prior to topcoat.
Would the White Pre-Kote Plus yellow if used in interior and not overcoated with gloss finish?
Most single part finishes tend to yellow in the dark but recover if exposed to light. For example, if used in dry bilge areas it would be wise to use the Blue-Gray Pre-Kote Plus as any yellowing would not be so noticeable.
Can I add other products/additives to Pre-Kote Plus?
No, you should never add any additives or materials that claim to improve specific properties of an AkzoNobel product unless it is specifically stated so on the technical data sheet or labels. Doing so would invalidate any claims for application or performance issues.
Can the product be sprayed?
We do not recommend that DIY users spray the product as it is unlikely that they would have the full correct PPE equipment and suitable ventilated application areas. Professionals may decide to spray apply the product. Pre Kote Plus can be sprayed with Special Thinner 216.
Questions and answers
Can Toplac Plus be applied over recently applied Brightside?
Yes, with light sanding with P400.
Can Brightside be mixed with Toplac Plus?
No. To avoid wasting any Brightside you might use it either as a first
coat before switching to Toplac Plus.
Can Toplac Plus be blended with Pre-Kote Plus?
Yes, follow recommendations as for Toplac Plus.
Can Toplac Plus be applied over Pre-Kote?
Yes, but the enhanced gloss and DOI levels of Toplac Plus may not be fully obtained.
Is Toplac Plus suitable for use on decks with Intergrip added, or
will it be too slippery?
We would recommend the use of Interdeck for decks. Toplac Plus would present the same finish as Brightside with Intergrip added and both would have very similar levels of slip resistance. Actual levels of slip resistance would vary depending on the level of Intergrip added and how evenly it was applied.
Do Toplac Plus colors match the previous Brightside colors
where the color name are the same?
Toplac Plus is not an exact match to Brightside due the new raw
materials used in Toplac Plus, but as with any manufactured color you should always ensure you have the same batch number product to complete any given job. Using Brightside with Toplac Plus of the same
code/color side by side for example may well show a tonal difference that can be affected by very slight color differences andgloss levels. It is best to use any Brightside you have as a first coat, perhaps blended with Pre-Kote Plus and finish with Toplac Plus.
Can I add other products/additives to Toplac Plus?
No, you should never add any additives or materials that claim to improve specific properties of an AkzoNobel product unless it is specifically stated so on the technical data sheet or labels. Doing so would invalidate any claims for application or performance issues. Flattening Agent for one part finishes can be used to create a variety of gloss, satin or matt effects.
Can the product be sprayed?
We do not recommend that DIY users spray the product as it is unlikely that they would have the full correct PPE equipment and suitable ventilated application areas. Professionals may decide to spray apply the product as they would have both. If sprayed Special Thinner 216 is recommended for Toplac Plus.
What equipment (roller/brush) should I use with Toplac Plus?
We recommend to use a fine, thermo-bonded foam roller. Suitable rollers are listed below:
4” High Density Foam Rollers (rounded edges)
6” Closed Cell Foam Rollers (flat edges, cut into 3” sections)
6” Ultra Smooth High Density Foam Rollers (rounded edges)
If a brush is required then any natural bristle brush would be recommended.
Finn ut mer
Off White
YLK192 (193)
White
YLK905 (905)
White
YLK905 (905)
Off White
YLK192 (193)
