Toplac-Plus and One-Up HR

Predstavljamo našu sljedeću generaciju, vrhunski sustav premaza za nadvodne dijelove plovila čiji jednokomponentni finiš jednostavan za primjenu daje rezultate profesionalne razine.

Toplac Plus, najbolji u klasi visokosjajni finiš s dugotrajnijom UV zaštitom koji se izvanredno lako nanosi valjkom, bez potrebe za izravnavanjem tragova, dostupan u punoj paleti jarkih boja. Posjetite international-yachtpaint.com i pogledajte dostupnost boja po zemljama

Snow White YLK000 (001)

Mediterranean White YLK184 (545)

Matterhorn White YLK198 (199)

Rescue Orange YLK265 (265)

Oyster White YLK194 (195)

Ivory YLK187 (812)

Cream YLK027 (027)

Fire Red YLK504 (504)

Mauritius Blue YLK904 (018)

Rustic Red YLK501 (501)

Bondi Blue YLK898 (016)

Lauderdale Blue YLK936 (936)

Sapphire Blue YLK830 (830)

Oxford Blue YLK993 (105)

Flag Blue YLK990 (992)

Platinum YLK151 (151)

Atlantic Gray YLK684 (289)

Jet Black YKL999 (051)

Yellow YLK101 (101)

Rochelle Red YLK299 (011)

Bounty YLK292 (350)

Donegal Green YLK541 (077)

One UP

Dva u jedan, temeljni premaz i međupremaz za jednokomponentne finiše

Smanjena složenost sustava za metalne podloge

Poboljšava glatkoću završne obrade dodanom zaštitom podloge

Formuliran za poboljšanje estetike premaza Toplac Plus

Sustav najbolji u klasi, s jednokomponentnim finišima International i palubnim bojama za sve podloge

Niže emisije VOC-a

Lako se nanosi četkom ili valjkom, izvrsna svojstva tečenja i izravnavanja

Lakše se brusi nego Pre-Kote, čime se smanjuje vrijeme potrebno između nanošenja slojeva

Naučite kako zamiješati One UP

Nanesite preko One UP-a, našeg jednodijelnog podlaka i temeljnog premaza u jednom, sa zaštitom podloge, posebno glatkom završnom obradom i niskim VOC-ima.

Toplac Plus

Vrhunski visokotrajni sjajni finiš za plovila

Završna obrada profesionalne kvalitete

Nova formula s poboljšanim tečenjem uklanja potrebu za izravnavanjem tragova ako se upotrebljava valjak

Bez brušenja između slojeva

Poboljšana UV zaštita za sjaj i zadržavanje boje

Iznimna razina sjaja

Saznajte više

Nikad nije bilo tako lako postići fantastični finiš.

Got questions? Check out our FAQ's

Pre-Kote Plus FAQ's

Toplac Plus FAQ's

Preuzimanja

Preuzmite letak i saznajte više o tome što Toplac Plus i One UP mogu učiniti za vas!

Pronađite trgovca

Kupite sada

Još uvijek trebate pomoć? Javite nam se! rota@ri.t-com.hr

Dostupne boje Odaberite boju

One UP Viskoznost i miješanje

1. Nakon otvaranja, ovaj proizvod izgledom i pod opipom može biti čvrst ili viskozan.

2. Bez zamješavanja proizvod neće teći ili se izliti iz limenke ako se ona okrene naopako.

3. One UP mora se temeljito promiješati kako bi se postigla odgovarajuća konzistencija.

4. Nakon što se temeljito promiješa proizvod bi trebao teći i izliti se iz limenke i kao takav spreman je za uporabu.

Questions and answers

Can Pre-Kote Plus and Pre-Kote be physically mixed together? No, they are not fully compatible with each other. Can Pre-Kote Plus be applied over Pre-Kote if half-way through a job? Yes. Can Pre-Kote be applied over Pre-Kote Plus? Yes, but not recommended as the full properties of Toplac Plus may not be obtained. Can Toplac be blended with Pre-Kote Plus? Yes, follow recommendations as for Toplac Plus. Can Pre-Kote Plus be applied over Interprotect? Yes. I have previously used a primer in timber bilges without overcoating because it was fast dry and easy to apply. Could I use Pre-Kote Plus for the same type of job? Yes, but use the Blue-Gray product.

Can Pre-Kote Plus be used on Clear Epoxies like West System, Hawk Epoxy, or System Three epoxies? No, it cannot not be directly applied due to the amine in the epoxy. Recommend to use either Epoxy Primekote 404/414 or InterProtect 2000E over this substrate and then finish off with Pre-Kote Plus as the final primer prior to topcoat. Would the White Pre-Kote Plus yellow if used in interior and not overcoated with gloss finish? Most single part finishes tend to yellow in the dark but recover if exposed to light. For example, if used in dry bilge areas it would be wise to use the Blue-Gray Pre-Kote Plus as any yellowing would not be so noticeable. Can I add other products/additives to Pre-Kote Plus? No, you should never add any additives or materials that claim to improve specific properties of an AkzoNobel product unless it is specifically stated so on the technical data sheet or labels. Doing so would invalidate any claims for application or performance issues. Can the product be sprayed? We do not recommend that DIY users spray the product as it is unlikely that they would have the full correct PPE equipment and suitable ventilated application areas. Professionals may decide to spray apply the product. Pre Kote Plus can be sprayed with Special Thinner 216.

Questions and answers

Can Toplac Plus be applied over recently applied Brightside? Yes, with light sanding with P400. Can Brightside be mixed with Toplac Plus? No. To avoid wasting any Brightside you might use it either as a first coat before switching to Toplac Plus. Can Toplac Plus be blended with Pre-Kote Plus? Yes, follow recommendations as for Toplac Plus. Can Toplac Plus be applied over Pre-Kote? Yes, but the enhanced gloss and DOI levels of Toplac Plus may not be fully obtained. Is Toplac Plus suitable for use on decks with Intergrip added, or will it be too slippery? We would recommend the use of Interdeck for decks. Toplac Plus would present the same finish as Brightside with Intergrip added and both would have very similar levels of slip resistance. Actual levels of slip resistance would vary depending on the level of Intergrip added and how evenly it was applied. Do Toplac Plus colors match the previous Brightside colors where the color name are the same? Toplac Plus is not an exact match to Brightside due the new raw materials used in Toplac Plus, but as with any manufactured color you should always ensure you have the same batch number product to complete any given job. Using Brightside with Toplac Plus of the same

code/color side by side for example may well show a tonal difference that can be affected by very slight color differences andgloss levels. It is best to use any Brightside you have as a first coat, perhaps blended with Pre-Kote Plus and finish with Toplac Plus. Can I add other products/additives to Toplac Plus? No, you should never add any additives or materials that claim to improve specific properties of an AkzoNobel product unless it is specifically stated so on the technical data sheet or labels. Doing so would invalidate any claims for application or performance issues. Flattening Agent for one part finishes can be used to create a variety of gloss, satin or matt effects. Can the product be sprayed? We do not recommend that DIY users spray the product as it is unlikely that they would have the full correct PPE equipment and suitable ventilated application areas. Professionals may decide to spray apply the product as they would have both. If sprayed Special Thinner 216 is recommended for Toplac Plus. What equipment (roller/brush) should I use with Toplac Plus? We recommend to use a fine, thermo-bonded foam roller. Suitable rollers are listed below: 4” High Density Foam Rollers (rounded edges) 6” Closed Cell Foam Rollers (flat edges, cut into 3” sections) 6” Ultra Smooth High Density Foam Rollers (rounded edges) If a brush is required then any natural bristle brush would be recommended.

Saznajte više

Off White YLK192 (193)

White YLK905 (905)

Off White YLK192 (193)